main

#include <ESP8266WiFi.h>
#include "config.h"

#define BLINKER_PRINT Serial
#define BLINKER_WIFI
#include <Blinker.h>

char auth[]  = "9bd88da46b95";//APP密鑰//

int R_VAL=202;
int G_VAL=215;
int B_VAL=0;
#define R_PIN 4             //定義LED2燈引腳
#define G_PIN 5             //定義LED1燈引腳
#define B_PIN 14             //定義LED5燈引腳
int buttonPin = 0;          // 按鍵的管腳定義
// 新建組件對象
BlinkerButton Button1("btn-abc");
BlinkerNumber Number1("num-abc");
BlinkerRGB    RGB1("col-9bf");
int counter = 0;

// 按下按鍵即會執(zhí)行該函數(shù)
void button1_callback(const String & state) {
    BLINKER_LOG("get button state: ", state);
     Button1.print("off");
    if(state=="on")
   { 
    R_VAL= 255;//越大越亮，三種燈的亮暗程度不同顯示不同的顏色，全亮//
    G_VAL= 255;
    B_VAL= 255;  
   }
   else if(state=="off")
   {
    R_VAL= 0;//全滅//
    G_VAL= 0;
    B_VAL= 0;
    }
    analogWrite(R_PIN, 1023-R_VAL*4);//將255放大1023，再將1023變成0，1022變成1······//
    analogWrite(G_PIN, 1023-G_VAL*4);
    analogWrite(B_PIN, 1023-B_VAL*4);  
}

// 如果未綁定的組件被觸發(fā)，則會執(zhí)行其中內容
void dataRead(const String & data)
{
    BLINKER_LOG("Blinker readString: ", data);
    
    counter++;
    Number1.print(counter);
}
void rgb1_callback(uint8_t r_value, uint8_t g_value,uint8_t b_value, uint8_t bright_value)
{
    digitalWrite(LED_BUILTIN, !digitalRead(LED_BUILTIN));
    BLINKER_LOG("R value: ", r_value);
    BLINKER_LOG("G value: ", g_value);
    BLINKER_LOG("B value: ", b_value);
    BLINKER_LOG("Rrightness value: ", bright_value);
    R_VAL= r_value;
    G_VAL= g_value;
    B_VAL= b_value;
    analogWrite(R_PIN, 1023-R_VAL*4);//將255放大1023，再將1023變成0，1022變成1······//
    analogWrite(G_PIN, 1023-G_VAL*4);
    analogWrite(B_PIN, 1023-B_VAL*4);
}

  
void setup() {
  
  Serial.begin(115200);
  Serial.println("star");//串口輸出打印//
  String name_1=reader("name");
  String pwd_1=reader("pwd");
  char name_2[name_1.length()+1];
  char pwd_2[pwd_1.length()+1];
  
  for(int i=0;i<name_1.length();i++)
    name_2[i]=name_1[i];
  name_2[name_1.length()]='\0';

  for(int i=0;i<pwd_1.length();i++)
    pwd_2[i]=pwd_1[i];
  pwd_2[pwd_1.length()]='\0';
  Serial.println(name_1);//串口輸出打印//
  Serial.println(pwd_1);//串口輸出打印//
  Serial.println(name_2);//串口輸出打印//
  Serial.println(pwd_2);//串口輸出打印//
  #if defined(BLINKER_PRINT)
        BLINKER_DEBUG.stream(BLINKER_PRINT);
  #endif
  // 初始化有LED的IO
  pinMode(LED_BUILTIN, OUTPUT);
  digitalWrite(LED_BUILTIN, HIGH);
  // 初始化blinker
  Blinker.begin(auth, name_2, pwd_2);
  Blinker.attachData(dataRead);
  RGB1.attach(rgb1_callback);
  Button1.attach(button1_callback);
  pinMode(R_PIN,OUTPUT);       //設定LED2引腳為輸出
  pinMode(G_PIN,OUTPUT);       //設定LED3引腳為輸出
  pinMode(B_PIN,OUTPUT);       //設定LED4引腳為輸出
  pinMode(buttonPin, INPUT_PULLUP); //設置按鍵管腳上拉輸入模式
}
char flag=0;
void loop() {
  if(flag==0)
  {
    Blinker.run();
    if (digitalRead(buttonPin) == LOW) { // 若按鍵被按下
      delay(100);
      if (digitalRead(buttonPin) == LOW) { // 延時消抖
        Serial.println("=============wifi config===============");//串口輸出打印//
        flag=1;
      }
    }
  }
  else if(flag==1)
  {
    myWebConfig_init();
    flag=2;
  }else if(flag==2)
  {
    myWebConfig_run();
   }
  
  //
}