BS type 1-C，單端口傳輸驗證型
BS type 1-H，
BS type 1-O and BS type 2-O，
一般關注BS type 1-C，單端口傳輸驗證型
FR1和FR2
band定義
傳輸帶寬配置
保護帶
多u傳輸時，保護帶
基站可配置的帶寬與SCS，band的關系
NR-ARFCN，RF reference frequency FREF以MHz表示
合法的NR-ARFCN與Band的關系
同步Raster
合法的GSCN與band的關系
射頻發射要求
6.2 Base station output power
6.3 Output power dynamics
6.4 Transmit ON/OFF power
6.5 Transmitted signal quality
輸出信號的頻率不可避免會有一定的偏差，我們用頻率誤差（Frequency Tolerance）或頻率穩定度（Frequency Stability），用單位ppm來表示，即百萬分之一（parts per million）（1/10^6），是相對標稱頻率的變化量，此值越小表示精度越高。比如，12MHz晶振偏差為±20ppm，表示它的頻率偏差為12×20Hz=±240Hz，即頻率范圍是（11999760～12000240Hz）
6.6 Unwanted emissions
射頻接收要求
7.2 Reference sensitivity level
7.3 Dynamic range，有干擾的AWGN信號進來，信號依然可以解析的能力
7.4 In-band selectivity and blocking
7.5 Out-of-band blocking
7.6 Receiver spurious emissions
7.7 Receiver intermodulation
7.8 In-channel selectivity
各個信道都有信號質量檢測需求
PUSCH
PUSCH傳輸預編碼使能
另外還有（最小要求只在小帶寬配置下時要求）：
PUSCH傳輸預編碼使能的情況
UCI復用PUSCH的情況
高速運動下的性能
2-Step RA，RRC Resume
等等
PUCCH
8.3.1 DTX to ACK probability
The DTX to ACK probability, i.e. the probability that ACK is detected when nothing was sent
- #(false ACK bits) denotes the number of detected ACK bits.
- #(ACK/NACK bits) denotes the number of encoded bits per slot
- #(PUCCH DTX) denotes the number of DTX occasions
8.3.3.1 NACK to ACK requirements
The NACK to ACK detection probability is the probability that an ACK bit is falsely detected when an NACK bit was sent on the particular bit position
- #Total NACK bits denotes the total number of NACK bits transmitted
- #NACK bits decoded as ACK bits denotes the number of NACK bits decoded as ACK bits at the receiver, i.e. the number of received ACK bits
- NACK bits in the definition do not contain the NACK bits which are mapped from DTX, i.e. NACK bits received when DTX is sent should not be considered.
8.3.3.2 ACK missed detection requirements
The ACK missed detection probability is the probability of not detecting an ACK when an ACK was sent.
8.3.4.2 UCI BLER performance requirements
The UCI block error probability (BLER) is defined as the probability of incorrectly decoding the UCI information when the UCI information is sent. The UCI information does not contain CSI part 2.
PRACH
8.4.1 PRACH False alarm probability
The false alarm probability is the conditional total probability of erroneous detection of the preamble (i.e. erroneous detection from any detector) when input is only noise.
8.4.2 PRACH detection requirements
The probability of detection is the conditional probability of correct detection of the preamble when the signal is present. There are several error cases – detecting different preamble than the one that was sent, not detecting a preamble at all or correct preamble detection but with the wrong timing estimation.
附錄
A1 - A5， FRC 1-5 parameters
A6， Prach preamble
A7-A9，F(xiàn)RC 7-9parameters
B， FR1的EVM定義，參考測量點等
C， FR2的EVM定義，參考測量點等
G，Propagation conditions，傳播環境，AWGN，多徑衰落
與多普勒頻偏組合時
還有MIMO信道相關矩陣，多普勒頻偏的定義等
